--- Skip to content
Practice2026-10-245 min read

Tying outlets and switches to furniture: 7 rules

First draw the furniture, then place the points: sockets live where the bed, desk and TV will stand, switches on the handle side of doors. Seven rules below put every outlet in reach before the walls are chased.

Author:GorkyCAD Team

Furniture plan first, points second

Every blocked socket has the same root cause: points were placed on an empty plan and furniture arrived later. Reverse the order — bed, wardrobes, desk, sofa, TV — and only then draw a single socket. The furniture layout is the foundation the electrics stand on.

Ask the customer for the furniture plan or sketch it together in ten minutes: overall dimensions, bed size, desk position, TV wall. Even a rough scheme beats none — corrections on paper cost nothing, while a socket behind a wardrobe costs a chase, plaster and paint.

Freeze the layout with a date and a signature — even a message confirmation works. Later “we moved the bed to the other wall” then becomes a documented change with a price, not a free redo of half the wiring.

Bedroom: nightstands, bed, TV

The bed zone eats the most sockets in the flat: two points per nightstand for chargers and lamps, plus power for an electric blanket or alarm. Place them just above the nightstand top so plugs fit but the sockets hide behind its edge.

The TV wall gets its own block: TV, console, router — three to four points at low height behind the stand. If the TV hangs opposite the bed, add sockets on both walls rather than betting on one arrangement surviving the first year.

Keep the bed sockets off the heavy groups: chargers and lamps are light, short-duty loads for the room group. What must never happen is a bed hidden in a corner with the only sockets two metres away across bare wall.

Living room and desk

The sofa zone mirrors the bedroom: floor lamp, chargers, laptop — two to three points per side, reachable without moving furniture. If a home cinema is planned, its wall gets a dedicated block like the TV zone.

The desk is the densest point in the home: computer, monitor, lamp, chargers and spares add up to four to six sockets. A desk block on its own small group is good practice — one tripped breaker then never darkens the whole room.

Think vertically too: a socket strip above the desk back edge beats crawling under the table. And leave one spare point on each free wall — the room layout will change, and a spare socket is the cheapest insurance against extension leads.

Doors and passages: switch sides

Switches obey doors, not walls: the switch belongs on the handle side of each door at hand height, so you meet it as you enter without reaching around the leaf. Draw the opening direction of every door before placing switches — a switch behind an open door is a dead switch.

Pass-through rooms and long corridors need control from both ends: two-way switching at each entrance. Stairs get a switch top and bottom. These are decided on the furniture plan too — a wardrobe placed later must not cover the only switch.

Check heights against the users: children, elderly, wheelchair — one walkthrough of the plan with the customer catches more than any norm. Mark every switch on the plan with its controlled luminaire so the installer wires intent, not guesswork.

Kitchen and hallway in brief

The kitchen follows the worktop, not the walls: sockets sit above the countertop in the cooking zone, plus dedicated points for built-in appliances. Count the appliances first — kettle, microwave, coffee machine — then place the blocks, not the reverse.

The hallway needs light control at every entrance, a socket for the vacuum cleaner and power for the router nook. Robe cupboards deserve a switching thought too: a motion-sensor light inside a deep wardrobe is a small joy of a good plan — and one the customer will remember you by.

Plan the router and low-current hub as its own powered, ventilated point: a router stuffed into a dead cupboard with no socket is a rework classic. An entry nook with a socket and trunking covers internet, intercom and cameras at once.

Balcony and utility corners get one or two weather-aware points by decision, not by leftover. If in doubt, add the spare — an unused socket costs little, a missing one costs a chase.

Freezing points before chasing

CheckpointQuestion to the customerIf “not sure”
Bed and nightstandsExact bed size and position?Fix one variant, add spares
Desk and TVWhich wall, what equipment?Blocks on both candidate walls
DoorsOpening directions final?Mark directions, place switches after
KitchenAppliance list complete?Two spare points over the top

Walk this table with the customer and freeze every row before the wall chaser starts. Each “we will decide later” is a future hole in finished plaster — the table turns vague wishes into signed points.

In GorkyCAD the agreed plan lives in the browser model: move a socket, and the routes, cable lengths, single-line diagram and estimate follow. Export the frozen plan to PDF so the agreement has a date and a version.

From plan to installation without rework

The handover chain is short: frozen furniture plan, points tied to it, routes to the panel, panel scheme, PDF set. If the furniture moves after freezing, re-tie the affected points the same day — a week later nobody remembers which socket followed which sofa.

Before printing, run the automatic checks — 25 checks against IEC 60364 in the English base — and confirm every group label matches across plan, single-line diagram and cable schedule. Calculations are advisory; the engineer approves the result.

Then hand over: open the editor, verify the points and warnings, and download the PDF package for the installers. Tariffs are on the pricing page (Pro €40/mo, start free).

After installation, walk the flat with the plan and labels: tag every group in the panel in plain words — “bedroom sockets”, “kitchen cooker”. Three years from now that tidiness will pay back at the first fault, found in minutes.

FAQ

What height for nightstand outlets?

There is no universal height: it follows the nightstand top plus a small margin for plugs and chargers. Fix the furniture dimensions first, then set the height so sockets stay reachable but hidden behind the nightstand edge.

Switch on the handle side?

Yes — the switch belongs on the handle side of the door, at hand height, so you hit it as you enter without reaching around the leaf. Mark the opening direction of every door on the plan before placing a single switch.

How many outlets per desk?

Plan for the computer, monitor, lamp, chargers and one or two spares — typically four to six points per full desk. A desk block on its own small group keeps a tripped breaker from darkening the whole room.

No furniture plan yet — what to do?

Arrange provisional furniture anyway: bed, wardrobes, desk, TV. Place sockets for that layout and add one or two spares on free walls. Moving a socket on paper is free; chasing a finished wall is not.

Tie sockets to furniture in GorkyCAD

Place the furniture plan, tie sockets to it and export the PDF set from one model. Start free in the browser.

Open GorkyCAD