--- Skip to content
Design2026-10-244 min read

Garage and parking electrical design: doors, light, sockets

A garage combines sectional doors, workbench loads and a compressor; an indoor car park adds wayfinding, presence control and fire requirements. The working answer: separate groups for doors, lighting and power tools, sensor control where the regime allows, fire-rated routing where required, and one document set — plan, panel, single-line and estimate — from a single model.

Author:GorkyCAD Team

Loads: doors, light, bench, compressor

Start with the load list, because a garage hides more consumers than it seems. Sectional or roller doors each bring a motor with inrush current plus control and safety edges. Lighting splits into general, local bench light and outdoor apron light. The workbench adds a compressor with heavy starting current, a welder or charger socket, and small power tools that all coincide on a Saturday morning.

A car park extends the list: wayfinding and numbering light, barrier and gate operators, ventilation and smoke-extract fans, drainage pumps, CCTV and access control power. Write every consumer with its rated power into one list before drawing a single group — the incomer size, the panel layout and the estimate all grow out of this table.

Lighting and how it is controlled

Garage lighting is working light first: uniform illuminance over the bench and parking bays, local spots over the workbench, and a lit apron outside the doors. In car parks add wayfinding — lit bay numbering, arrows and pedestrian paths — plus permanent light on ramps, exits and barriers where sensors are not permitted to switch it off.

Control strategy saves more than efficient luminaires: two-point switching for the garage (entrance plus house door), presence sensors for aisles and storage corners, dusk relays for the apron. Set time delays with margin so vehicles do not outrun the light cone, and keep sensor-controlled and permanent circuits on different groups so one fault never darkens the whole level.

Groups and panel: what sits apart

The group schedule is deliberately boring: lighting on its own groups, each door operator on a dedicated group, bench sockets on one or two power groups, compressor and welder each dedicated, outdoor and sensor circuits separate. Segregation means a jammed door or a faulty grinder never kills the light you need to fix it.

The panel stays compact but legible: incomer with metering, grouped rows with a printed legend, RCD protection where the location rules require it, and two or three spare ways for the next owner — a lift, a heater, a second compressor. Automatic checks against 25 IEC 60364 rules flag missing protection and wrong groupings while the scheme is still on screen, before cables are bought.

Fire requirements and cable routes

Underground and attached car parks are fire-regulated spaces: ventilation and smoke extract, fire alarm interfaces, and cable routes that survive long enough for evacuation. Power for fire systems sits on dedicated groups, clearly marked and independent of general circuits, and penetrations through fire partitions are sealed with rated solutions.

Route choice follows the building: tray or ladder for long car-park runs with room for a spare cable, conduit for surface garage drops exposed to impact, burial-rated methods for the yard feed. Keep power and fire-alarm routes separated per the project requirements, and record every route on the plan so the fire inspector and the next electrician read the same drawing.

Documents and handover

The handover set for a garage or small car park mirrors any small power project: floor plan with points, luminaires and routes, panel schedule with breaker ratings, single-line diagram generated from the model, cable schedule, bill of quantities with a price date, and the estimate. The fire-system interfaces and sensor schedules go in as separate sheets, not as margin notes.

Because everything derives from one model, a late change — one more door, a moved bench, an extra sensor zone — regenerates the single-line, the schedules and the quantities together. Hand over the PDF set plus the exchange files the client actually needs, and note the revision and the price date on every sheet.

Common mistakes in garage projects

The most expensive mistake is one group for everything: doors, light and bench on a single breaker, so every fault ends in darkness with a half-open door. Next comes lighting without control strategy — burning 24/7 in an empty car park — and sensors wired so that ramps and exits go dark between cars. Undersized feeds to the compressor and welder, guessed instead of calculated, complete the classic set.

Documentation mistakes cost nearly as much: no legend in the panel, no route plan for buried yard feeds, an estimate without a price date. A buried cable nobody mapped is a cable somebody digs through — the plan is cheaper than the second excavation.

Build it in GorkyCAD: one model, full set

Draw the garage or parking level, place luminaires, sensors, door operators and bench points, and divide groups right in the model. The single-line diagram is generated automatically, the panel is assembled with phase balancing, and the deterministic calculation engine checks heating, voltage drop and fault currents — with results that stay preliminary until the responsible engineer approves them.

The export is a PDF set — plan, single-line, panel schedule, cable schedule, bill of quantities and estimate — plus DXF, XLSX, IFC, BCF and GLTF on the Pro plan. Start free in the browser with offline PWA support, and move to Pro at €40/mo when limits or full calculations and exports are needed. Electric-vehicle charging is a separate design topic with its own feeder logic and is deliberately out of scope here.

FAQ

Should doors and lights sit on separate groups?

Yes — that is the recommended split. Doors carry motors with inrush currents and their own control circuits, while lighting must stay on for safe evacuation and fault-finding. A jammed door or a shorted operator must never take the lights with it. Keep emergency and standby lighting on yet another independent path where the code requires it.

Which cable suits a cold garage?

Choose cable with a sheath rated for the actual operating temperature and mechanical exposure: unheated garages see frost, condensation and occasional impact, so surface routes in conduit or tray beat loose plastered runs. Verify the cross-section against heating and voltage drop for the real route length, and let the engineer confirm the final choice — catalogue data alone is not a design.

Do motion sensors make sense in a car park?

Yes, where the operating regime allows: presence and motion sensors cut idle burning in aisles, stair cores and storage corners while keeping entrances and ramps lit. Use dusk-aware settings and sensible time delays so cars and pedestrians do not outrun the light cone. Critical zones — exits, ramps, barriers — stay on permanent or standby lighting regardless of sensors.

Is pipe trace heating needed?

Only where the design explicitly provides it: trace heating for exposed water pipes or gutters is its own dedicated group with thermostat control, not an afterthought on a socket circuit. In a plain parking box with drained pipes there is usually nothing to heat. Decide it at the load-list stage, because retrofitting means new routes through finished concrete.

Assemble the plan, panel and single-line from one model — open the editor

Draw the garage or car-park plan, divide door, light and bench groups, generate the single-line diagram and export the PDF set. Start free in the browser — Pro at €40/mo when the job grows.

Open GorkyCAD