Philosophy: prescriptive rules versus performance goals
The deepest difference is not voltage but philosophy. The NEC (NFPA 70) is prescriptive: it tells you where receptacles must sit, which rooms need GFCI and AFCI, and how far apart outlets may be. Follow the article, pass inspection. IEC 60364 is principle-based: it states protection goals — against shock, thermal effects, overcurrent — and leaves the how to national implementations and engineering judgement.
BS 7671 sits on IEC foundations with strong national habits: rings, fused plugs, certificate culture. The PUE tradition prescribes radial groups, staged protection and detailed installation rules. Neither approach is lazy; they place responsibility differently — the NEC on the rule text, IEC on the designer applying the principles.
Practical consequence: moving between systems means relearning what is fixed and what is judgement. A designer used to asking «which article?» will find IEC annexes vague; one used to principles will find the NEC refreshingly — or suffocatingly — specific.
Sizing and heating: AWG, millimetres and current-carrying capacity
All four systems obey the same heat equation — continuous current must not overheat insulation — but the tables differ. IEC works in square millimetres with installation-method correction factors; the NEC works in AWG with its own ampacity tables and derating; the PUE uses millimetres with laying-condition coefficients; BS 7671 follows IEC-style sizing with UK installation methods.
- Conductor scales do not convert roundly: 12 AWG is about 3.31 mm², 14 AWG about 2.08 mm² — always use a proper AWG to mm² map, never mental arithmetic.
- Correction factors multiply: grouping, ambient temperature and installation method each take their cut in every system.
- Breaker and cable must agree in the same logic — an IEC-sized cable under a NEC-sized breaker rule is a coordination failure, not creativity.
Tooling helps here: a deterministic calculation core repeats load, short-circuit and drop maths identically every run, with methods rooted in IEC 60364 and national codes. Results stay preliminary working material until the responsible engineer signs them.
Protection and RCD thresholds: shock, fire and selectivity
Every system protects people with residual-current devices and installations with overcurrent devices — but the thresholds and habits differ. BS practice puts 30 mA on socket outlets as standard; IEC 60364 requires 30 mA additional protection in defined cases and special locations; the NEC achieves similar outcomes with GFCI at 5 mA trip levels in wet and outdoor locations plus AFCI against arc faults in living areas; PUE practice stages 30 mA for sockets and 10 mA for wet rooms.
Selectivity carries the universal warning: full selectivity exists only with manufacturer-verified time-current characteristics; without passport data any claim is partial or conditional. This is true in London, Chicago and Moscow alike — record the boundary you actually verified.
When comparing, compare complete chains — upstream device, downstream device, fault loop — not single thresholds torn out of context. A 30 mA number means little without the system (TN-S, TT) and the disconnection-time requirement behind it.
Voltage-drop limits: the 5% family and its cousins
Voltage drop is where the four systems look most alike: everyone limits it to single-digit percent, because motors stall and lamps dim on the same physics everywhere. IEC practice commonly works within a few percent from origin to point of use; the NEC recommends — informatively, not mandatorily — about 3% on branch circuits and 5% overall; BS follows the IEC-family approach; PUE-side engineering commonly holds 5% total with a 3% lighting warning in tooling.
Design habits follow the numbers: long runs get upsized, sub-distribution is placed close to load centres, and lighting — the most drop-sensitive load — is checked first. Whatever the nominal limit, the check must run on the actual route lengths, not on a guess.
In GorkyCAD voltage drop, short-circuit loop and heating checks run inside the deterministic core from the same model that draws the plan — see the features page for the calculation set. Reminder: tool results are preliminary; the engineer approves and signs.
One installation, one standard: why mixing fails
The most expensive mistake in multi-standard work is blending: NEC receptacle spacing with IEC protection philosophy and PUE paperwork. Each system assumes its own coherence — device ratings, verification tests and certificate formats interlock. A hybrid satisfies nobody and fails every verifier.
- Pick the governing standard by installation address and client contract before design starts.
- Keep device selections, cable tables and test procedures inside that single system.
- Study other standards to choose wisely — then commit to one for the issued pack.
For export portfolios the sane unit is one model per target standard: a US variant in NEC logic, a UK variant in BS logic, sharing geometry but not protection decisions. That is cheaper than converting a finished design under deadline pressure.
One tool for four standards: how to organise the work
GorkyCAD declares four standards in one engine — on the EN side presented as IEC, IS, ANSI and BS — with 25 IEC 60364 checks, a single-line to IEC 60617, auto panel with phase balancing, and document export; scope and limits are on the EN pricing page (Pro €40/mo, start free without a card).
The workflow that survives audits is boring: one model holds plan, single-line, panel, cable schedule, bill of materials and estimate, so a protection change propagates to every sheet. The deterministic core — not an LLM — repeats the maths identically, while the AI assistant handles placement hints, checks and drafting help within its token limits.
Organise multi-standard work as parallel variants of one geometry: same rooms and routes, different protection logic per market. Version the variants explicitly so the UK pack never ships with the US schedule.
Where to look up clauses without drowning
Each system has a canonical entry point; learn the map once and stop googling fragments.
- IEC 60364: parts 4 (protection) and 5 (selection and erection) plus the national annex of the target country — the annex, not the base text, decides the project.
- NEC (NFPA 70): Article 90 introduction, 210 branch circuits, 250 grounding, 300 wiring methods; new edition every three years — confirm which one the state adopted.
- BS 7671: the 18th edition with amendments via the IET; certificates reference the exact edition and amendment.
- PUE: chapters 1.7 and 3.1 for protection plus GOST/SP checks — on the RU side GorkyCAD runs 41 PUE/GOST/SP checks.
And the meta-rule: when forum advice quotes a clause number without an edition, treat it as a rumour. Standards move; editions and amendments are part of the citation.
FAQ
Which standard is strictest?
None is universally strictest — each is strict in its own place. The NEC is famously prescriptive about receptacle placement and GFCI/AFCI coverage, BS 7671 about rings and 30 mA socket protection, IEC 60364 about structured verification, and the PUE about staged RCD thresholds. Ask which standard governs the installation address, and design to that one.
Can approaches be mixed?
No — at least not inside one installation. Protection coordination, cable sizing assumptions and verification paperwork assume a coherent system. You may study several standards to choose, but the issued design follows one, recorded on the certificates. Mixed justifications are the first thing any verifier rejects.
Which standard for export jobs?
Design natively to the market where the building stands: NEC logic for the US, BS 7671 for the UK, IEC 60364 with national annexes for most other export markets. Native design beats conversion — device ratings, wiring habits and certificate formats differ too much to relabel afterwards. Keep one model per target standard.
Where are calculation methods published?
Start with the standard text itself plus its national annexes, then the tool documentation: in GorkyCAD the declared logic is IEC, IS, ANSI and BS with 25 IEC 60364 checks on the EN side — scope and limits are on the pricing page. Calculation results anywhere remain preliminary until the responsible engineer approves them.
Related articles
- NEC and IEC in one tool
- IEC 60364 explained: the international base
- IEC 60364 special locations: wet and special rooms
- Voltage-drop limits: how to check them
Four standards, one model — compare them in the editor
Switch the same model between IEC, ANSI and BS logic, generate the single-line and panel from one source, and run 25 IEC 60364 checks. Start free — Pro is €40/mo.
Open GorkyCAD