NEC structure: which articles a small project lives in
The NEC — NFPA 70 — is organised in chapters and articles, and a small residential or fit-out project lives in a handful of them. Article 90 sets the purpose and scope; Article 210 covers branch circuits including receptacle and lighting rules; Article 250 covers grounding and bonding; Article 300 covers wiring methods. Learn those four and the code stops looking like a phone book.
Two administrative facts decide everything. First, the NEC is reissued every three years, so clauses move between editions. Second, states and cities adopt editions with their own amendments and delays — the «current NEC» nationally may not be the enforced code locally. The authority having jurisdiction (AHJ) and its adopted edition go on the first sheet of your documents.
Read the NEC as a prescriptive checklist: where devices must be, which rooms need which protection, how far apart receptacles may sit. Engineering judgement fills the gaps the articles leave, but the articles — not the judgement — pass inspection.
AWG to mm²: the conversion table you actually need
American Wire Gauge runs backwards from intuition: smaller number, thicker wire. Memorise the working band for small projects and keep the table on the drawing.
| AWG | Approx. mm² | Typical small-project use |
|---|---|---|
| 14 | 2.08 | 15 A lighting and general receptacle circuits |
| 12 | 3.31 | 20 A small-appliance and bathroom circuits |
| 10 | 5.26 | 30 A fixed loads (dryer-class, water heater-class) |
| 8 | 8.37 | 40–50 A ranges and large fixed loads |
| 6 | 13.3 | Feeders and large equipment |
Three warnings travel with the table. First, ampacity depends on insulation rating and derating (ambient, grouping, conduit fill) — the table gives size, the code tables give current. Second, never upsize the breaker without rechecking the wire. Third, for export documentation show both designations: AWG for the US inspector, mm² for everyone else.
Receptacles, kitchens, baths: where outlets must be
Article 210 is famously specific about receptacle placement, and inspectors check it first. The headline rule for living areas: spacing such that no point along the wall is far from a receptacle — the classic 12-foot spacing with 6-foot reach — so cords never stretch across the room. Hallways, kitchens and countertops each get their own spacing and coverage logic.
- Kitchens: dedicated 20 A small-appliance branch circuits for countertop receptacles, GFCI-protected, with the number of circuits set by the edition.
- Bathrooms: dedicated 20 A circuit logic with GFCI protection on receptacles near water.
- Laundry, garage, outdoors: dedicated or protected coverage per article — these are the rooms that fail inspections most often.
Design habit: draw the receptacle layout against the furniture plan first, then assign circuits. Moving a receptacle after circuits are scheduled means re-coordination of protection, cable schedule rows and panel ways — cheap on day one, expensive at handover.
GFCI and AFCI rooms: shock versus arc protection
Two different dangers, two different devices. GFCI (ground-fault circuit interrupter) guards people against shock in wet and outdoor locations — bathrooms, kitchens near sinks, garages, exteriors, laundry — tripping at a few milliamps. AFCI (arc-fault circuit interrupter) guards the building against fire from arcing faults in living areas such as bedrooms and living rooms.
Coverage expands with every edition, so the room list must be read in the adopted edition, not remembered from the last job. Dual-function AFCI/GFCI devices exist where both protections meet in one room — kitchens and laundry are the usual candidates — but verify acceptance with the AHJ before standardising on them.
Compare honestly with IEC habits: the function overlaps the 30 mA RCD world, but thresholds, test procedures and mandated rooms differ. Map per room, per adopted edition — equivalence slogans fail inspections.
Grounding, bonding and the service: what to verify
Article 250 grounding and bonding is the least forgiving part of a small NEC project. The service gets a grounding electrode system, the neutral is bonded to ground at the service — once — and downstream subpanels keep neutral and ground strictly separated. One extra neutral-ground bond in a subpanel is a classic inspection failure.
- Electrode system present and connected at the service, with sizing per article.
- Single neutral-ground bond at the service; isolated neutrals everywhere downstream.
- Bonding of metal piping, structural steel and equipment grounds continuous back to the source.
On drawings this means the single-line must show the bond point explicitly and every subpanel labelled with separated N and PE bars. A model-generated single-line that derives bars from the same data as the plan cannot silently disagree with it.
NEC versus IEC: what to recheck on conversion
Converting an IEC-habit design to NEC logic means rechecking five things, not translating words. Supply voltages differ (120/240 V systems versus 230 V); conductor sizing switches from mm² tables to AWG ampacity tables; colour codes change function; receptacle placement becomes prescriptive rather than customary; and protection splits into GFCI/AFCI coverage instead of staged RCD thresholds.
The honest workflow is native design: start the US variant from NEC articles, keep the IEC variant in IEC logic, share only geometry between them. Protection decisions, schedules and certificates stay per-market, per edition.
Calculation discipline is identical in both worlds: loads, fault currents, voltage drop and heating run on actual route lengths with stated assumptions, and every result is preliminary working material until the responsible engineer approves and signs it. Tools recommend; engineers decide.
A small NEC project in one consistent tool
GorkyCAD declares NEC/ANSI among its four supported standards, so receptacle layouts, GFCI/AFCI zoning and AWG-based schedules live in the same model as the plan, the single-line, the panel, the bill of materials and the estimate — one change propagates to every sheet instead of stranding the cable schedule.
The calculation core is deterministic rather than AI-based: load, fault and voltage-drop maths repeat identically on every run, with methods rooted in IEC 60364 and national codes. The EN product line adds 25 IEC 60364 checks, full panel tooling with phase balancing, and document export (PDF, DXF, XLSX, IFC, BCF, GLTF); scope, limits and the €40/mo tariff are on the EN pricing page, and you start free in the editor.
Close a small US job the boring way: adopted edition noted, receptacle spacing verified against Article 210, GFCI/AFCI rooms checked per edition, single bond at the service — then issue the pack.
FAQ
AWG in plain words?
American Wire Gauge: a wire-size scale where smaller numbers mean thicker wire — 12 AWG (about 3.31 mm²) is heavier than 14 AWG (about 2.08 mm²). Homes commonly use 14 AWG on 15 A circuits and 12 AWG on 20 A circuits. Never convert by feel; keep a proper AWG to mm² table on the project sheet.
Is a GFCI an RCD?
Roughly — a GFCI is the American device for additional protection against electric shock, tripping around 5 mA, much like the function of a European RCD. Differences sit in thresholds, test rules and where each code mandates them, so map requirements per room rather than assuming one-for-one equivalence.
Where are AFCIs required?
AFCI protection is required in the living areas the adopted edition lists — typically bedrooms, living rooms and similar spaces — with exact scope varying by edition and state amendments. Confirm which NEC edition the authority having jurisdiction adopted before you place a single device, and record the edition on the drawings.
Which NEC edition applies?
The NEC is reissued every three years; 2023 is the recent base edition, with the next cycle following. But the edition that matters is the one your state or city adopted — adoption lags and amends. Always verify locally and note the enforced edition in the project documents.
Related articles
- NEC and IEC in one tool
- AWG to mm² converter: size any wire
- IEC 60364 special locations: wet and special rooms
- RCD vs RCBO: what to put where
NEC basics for a small project — lay it out in the editor
Lay out receptacles, GFCI/AFCI zones and the AWG schedule from one model, and generate the panel and documents consistently. Start free — Pro is €40/mo.
Open GorkyCAD