--- Skip to content
Design2026-10-245 min read

Rented commercial unit: flexible design for tenant churn

A rented unit outlives its tenants: a cafe today, a salon tomorrow. The short answer: the landlord builds the base once with margin — an incomer with spare capacity, a panel no more than two-thirds filled, trays with room for new cables — and records boundaries, demands and sub-metering in the lease and handover act.

Author:GorkyCAD Team

Landlord base-build: incomer, metering, panel

A rented unit will outlive its tenants, so the landlord builds the base once and with margin: an incomer with spare capacity, main metering and a panel with spare ways. Today it is a coffee shop with a heated display, tomorrow a salon with a dozen dryers: rebuilding the incomer for each is slow and costly, while margin is provided once.

Base elementMinimumWhy the spare
Incomer and meteringContracted size + marginNew tenant, no new supply application
PanelNo more than ~70% filledGroups for refits
RoutesTrays with spaceNew circuits without opening finishes

Fix the responsibility boundary at once: what belongs to the landlord (incomer, metering, risers) and what the tenant fits out (wiring, light, sockets). That boundary later saves the scarcest resource — end-of-lease disputes.

The allocated demand and connection point are fixed by the utility's connection terms: they set the ceiling no new application can bypass. Keep them with the design — every incoming tenant and their designer first asks “how many kilowatts, and from where”. If old connection papers no longer match the incomer after refurbishments, reconcile the documents before marketing the unit, not mid-negotiation.

Spare routes and sockets

The cheapest flexibility is routes. Spine trays along corridors and service zones with connection points let every tenant pull their own circuits without opening neighbours' finishes. Tenants usually fit out sockets and lighting themselves, but the outlets and sleeves for them are provided upfront.

  • Trays with spare space — new cables without stripping ceilings.
  • Perimeter connection points — kitchens, displays, workstations.
  • Dedicated groups for signage and exterior light.
  • Floor-penetration sleeves — with spares.

The rule is simple: copper and tray installed at base-build cost less than any chasing under a trading tenant.

Sub-tenant split: metering and boundaries

When a unit is subdivided, each part gets its own boundary: a breaker in the common panel, a sub-meter and a stated permitted demand. Then bills split by metering, not “fifty-fifty”, and the bakery with ovens stops arguing kilowatts with the office. Sub-metering every part costs less than any dispute.

Record ownership boundaries and permitted demands in the handover record and lease schedule: who pays for what, who maintains their panel, what is reinstated at exit. A cable schedule keeps track of which circuit belongs to whom as tenants churn.

Mount sub-meters in a lockable compartment of the common panel or in a floor panel with sealed terminal covers — readings must be takable without access to other tenants' breakers. Write the reading and reconciliation procedure into the lease: who reports, when, and what counts as the billing reading in a dispute. Without that procedure even accurate meters become dispute fuel.

Sharing kilowatts fairly

Kilowatts are shared by contract, not by “who switched on first”. The sum of permitted demands must not exceed the unit's allocated supply — otherwise the incomer breaker becomes the dispute arbitrator, tripping everyone at once. Common loads (corridors, signage, ventilation) are metered separately and shared pro-rata or by agreement.

Load calculations and voltage-drop checks to the farthest points run in a deterministic standards-based engine, not a language model — results are repeatable. But calculations are preliminary: the engineer approves them, and the set counts as preliminary materials until signed. Exceeding the permitted demand means revisiting the contract, not “fitting a bigger breaker” — allocate new tenants from the base-build reserve instead of redistributing between existing ones. If the reserve falls short, apply for extra supply capacity months ahead, before signing a heavy tenant. Any refit is cleared in writing with an updated scheme, and the tenant hands over the as-built of their fit-out at exit. Keep the updated scheme and schedule with the lease so the full change history stays readable years later.

Handover and dilapidation pack

On move-in the tenant receives a pack: the plan with boundaries and connection points, the panel schedule marking “their” breakers, the permitted-demand list and the condition record. On move-out the same pack governs acceptance: what was removed, what reinstated, sub-meter readings. Photographic condition records are a mandatory part.

In GorkyCAD the whole pack exports as one PDF set from a single model: plan, single-line, panel schedule, specification, cable schedule and estimate. The estimate builds from one canon — materials and labour — with 14-day price freshness: the landlord sees the honest base-build cost, the tenant the cost of their fit-out. That settles the main question — “where did this price come from”.

Classic rented-unit mistakes

  • An incomer sized “just enough” for tenant one: tenant two needs a supply application and months of waiting.
  • A panel with no spare ways: every refit means a new panel.
  • No sub-metering: bills split “evenly”, disputes guaranteed.
  • Unrecorded boundaries: at exit nobody remembers whose circuit is whose.
  • Routes with no spare: a new circuit only by opening finishes.
  • An estimate with no price date: unrecognisable figures six months on.

Automated checks — 25 checks to IEC 60364 — catch some violations before installation, but boundaries, money and liability are fixed by people and contracts, not automation.

Building a fit-out-ready design in GorkyCAD

Draw the unit in the browser: one model links the plan with routes, the single-line, the panel with spare ways, the specification and the estimate. Show sub-tenant splits as separate groups with metering — the cable schedule will remember whose circuit is whose. The single-line generates automatically, and the estimate with 14-day price freshness justifies the budget to the owner.

Start free in the editor, and build the churn-proof design on Pro at €40/mo. Open the editor and lay out the unit base-build →

FAQ

What spare capacity for unknown tenants?

A rule of thumb: incomer and panel with margin for the next-heaviest profile — usually food service with thermal equipment. In practice that means a panel no more than two-thirds filled, trays with room for new cables and perimeter connection points. The engineer sizes the exact margin from the allocated supply and the network contract — calculations stay preliminary until signed.

How to split power between sub-tenants?

Give each part a contracted permitted demand, a sub-meter and its own breaker in the common panel; the permitted demands must sum within the unit's allocation. Meter common loads — corridors, ventilation, signage — separately and share them pro-rata. Bills then split by fact, and the incomer breaker never arbitrates disputes.

Who pays for electrical refits?

The base — incomer, metering, risers and a panel with spares — is normally the landlord's: it stays with the unit. Tenant-specific fit-out — light, sockets, equipment — and reinstatement at exit sit with the tenant unless the lease says otherwise. Record all of it in the lease and the condition report, never verbally.

What goes into the handover record?

Ownership boundaries, each part's permitted demand, all meter readings, the list of “their” breakers in the panel and photographic condition evidence. At exit the same record governs acceptance: what was removed, what reinstated. The project's cable schedule settles “whose circuit is whose” years later.

Lay out the unit base-build from one model

Draw the unit, build the panel with spares and export the PDF pack with the estimate for the owner. Start free in the browser — Pro €40/mo.

Open GorkyCAD