Daisy-chain vs star in practice
A daisy-chain (radial chain) runs one cable from the panel through each socket in turn: the incoming and outgoing conductors meet inside the socket terminals. It is the cheapest way to feed a row of general-purpose sockets — one group, one route, minimum cable.
A star (home-run) layout runs a separate cable from the panel — or from a local junction box — to each socket or small cluster. There are no pass-through terminals: every point has its own line back toward the panel. It costs more cable and more panel ways, but each line is independent.
A mixed layout combines both: chains where sockets stand along one wall and loads are small, stars where independence matters. In practice most flats and offices end up mixed — the question is only where to draw the line between the two approaches.
Cable and voltage drop compared
A daisy-chain wins on cable length: one route serves several points, and the total metre count is the lowest of all options. The price is cumulative current — the first segment of the chain carries the whole group load, so the voltage drop to the farthest socket grows along the chain.
A star spreads the current across independent lines, so the drop on each line depends only on its own load and length. Long routes to remote rooms become more predictable, and adding one more socket never degrades the neighbours.
Whichever topology you choose, check the farthest point: the total voltage drop is limited to 5%, with a warning already at 3% for lighting. GorkyCAD computes route lengths from the floor plan and checks voltage drop with its deterministic engine, so a chain that is too long shows up before installation, not after.
Fault-finding and repair
This is where the star pays back. A fault on one line disconnects one socket or one room; the rest keeps working, and the electrician tests a single cable with two ends. There is no need to open every socket in a row looking for a loose pass-through terminal.
In a daisy-chain one bad contact can kill everything downstream of it while the first sockets look alive — the classic “half the room is dead” symptom. Finding the break means opening boxes one by one along the route, which takes longer and disturbs finished walls.
Consider also the future: a star lets you move one socket to its own breaker or extend one room without touching the rest. A chain alteration means breaking into the middle of a live route. If the customer often rearranges rooms — offices, rentals — this argument alone favours the star.
What fits a flat, a house, an office
| Building | Recommended | Why |
|---|---|---|
| One-room flat | Chains per room + dedicated heavy groups | Short runs, drop is small, budget matters |
| House | Mixed, stars to remote rooms | Long routes, fault-finding across floors is costly |
| Office / rental | Star to work zones | Frequent rearrangement, uptime per zone |
In a typical flat, group sockets by room: one chain per room for general sockets, and separate lines for the cooker, oven, washer and boiler. That keeps the panel compact while heavy loads stay independent.
In a house, run stars to distant rooms and floors even for ordinary sockets: opening finished walls on two floors to find a broken chain costs more than the extra cable. Offices and rented spaces get stars to each work zone so one fault never stops the whole floor.
Topology and the panel: groups and breakers
Every topology decision lands in the panel. Daisy-chains merge into fewer groups and fewer breakers; stars need more ways, more cable entries and a tidier schedule. Before promising the customer “a small neat panel”, count the groups the topology actually requires.
Keep heavy appliances on their own breakers regardless of topology — that is a load rule, not a wiring-style rule. General sockets can share, but mixing a washer into a bedroom chain to “save a breaker” is exactly how nuisance tripping starts.
GorkyCAD assembles the panel from the same model as the plan: device selection, DIN-rail layout and phase balancing come from one source. Change a chain into a star on the plan and the panel scheme, the cable schedule and the estimate update together — no separate redrawing.
Common daisy-chaining mistakes
- Chaining heavy appliances together with general sockets — the group trips under combined load.
- Overlong chains through half the flat — the farthest socket fails the voltage-drop check.
- Pass-through terminals as the only connection — one loose terminal kills the whole downstream row.
- No spare ways in the panel — a future star or a new group has nowhere to go.
- Topology drawn only “in the head” — the installer chains differently than the designer meant.
Almost all of these are caught on paper: list the loads per chain, measure the longest route, and leave two to three spare ways in the panel. The automatic checks help too — GorkyCAD runs 41 checks against PUE/GOST/SP in the Russian base and 25 checks against IEC 60364 in the English one.
Showing topology in the project
Draw topology so the installer cannot misread it: chains as continuous routes through named sockets, stars as separate lines back to the panel or junction box. Every group gets a label matching the panel schedule and the single-line diagram.
The single-line diagram in GorkyCAD is generated from the model rather than drawn by hand, using GOST 2.702-2011, 2.755-87 and 21.210-2014 symbols — so the plan, the panel scheme, the cable schedule and the estimate always agree. Edit the topology once, regenerate the whole set.
Finish with the handover set: open the editor, verify drops and checks, and export the PDF package — plan, single-line diagram, panel scheme, specification, cable schedule and estimate. Tariffs and limits are listed on the pricing page (Pro €40/mo, start free).
Calculations are advisory; a qualified engineer approves the final design.
FAQ
Can every socket be daisy-chained?
No. A daisy-chain suits only low-power general-purpose sockets along one route. Heavy appliances — cooker, oven, washer, boiler, air conditioner — get their own groups, and long chains raise voltage drop and complicate fault-finding.
How many sockets can one chain hold?
There is no single universal number: it depends on the connected load and the length of the run. The practical rule is to keep high-power devices out of the chain and to check the voltage drop of the farthest socket — the limit is 5% in total.
Is star wiring always more expensive?
Not always. A star uses more cable, but it simplifies fault-finding, repair and later alterations. In a small flat with short runs the difference is modest; in a house or an office with long routes it becomes noticeable.
How does topology affect the panel layout?
Topology defines the number of groups and cable schedules: daisy-chains merge into fewer breakers, stars need more ways and a tidier layout. In GorkyCAD the panel is assembled from the same model as the plan, so any change in topology is reflected in the panel scheme.
Related articles
- Cable routing: best practices
- Voltage drop: real cases
- Cable sizing guide
- Wire connections: reliable methods
Try the topology in GorkyCAD
Draw the socket layout on the plan, generate the single-line diagram and the PDF set from one model. Start free in the browser.
Open GorkyCAD